焊烟没吸住,先别怪滤筒不行
发布时间:2026-11-09 发布来源:http://www.sdcjtz.com/

焊接车间那层蓝灰色烟,不是“有点呛”的小事。它混着锰、铬、氧化铁亚微米颗粒,粒径小、飘得远,罩口偏一点、风量差一截,呼吸带浓度就超标。

The layer of blue gray smoke in the welding workshop is not a small matter that feels a bit choked. It is mixed with submicron particles of manganese, chromium, and iron oxide, with small particle size and drifting far away. If the hood is slightly biased and the air flow is poor, the concentration in the breathing zone will exceed the standard.

生成高清放大图片-(16)

选设备先看工位形态,不先比参数:

Choose equipment first by looking at the workstation form, without comparing parameters:

1–2个零散手工焊:移动式单/双臂净化器,风量按1000–1500m³/h/工位,带火花阻火网+PTFE覆膜滤筒,插电就用;

1-2 scattered manual welding: mobile single/double arm purifier, air flow rate of 1000-1500m ³/h/workstation, equipped with spark arrester and PTFE coated filter cartridge, plug in and use immediately;

3–6个固定工位:壁挂或吊顶吸气臂+小型集中主机,不占地面;

3-6 fixed workstations: wall mounted or suspended suction arm+small centralized host, not occupying the ground;

7工位以上、机器人连续焊:集中式滤筒除尘,前置火花沉降+脉冲反吹,变频风机按开工数调功率,省电也省滤芯。

7 or more workstations, robot continuous welding: centralized filter cartridge dust removal, pre spark settling+pulse back blowing, variable frequency fan adjusts power according to the number of starts, saving electricity and filter elements.

三个工程细节容易翻车:

Three engineering details are prone to overturning:

捕集距离:吸气臂罩口离焊点尽量200–300mm,每远10cm,所需风量成倍涨;

Capture distance: The suction arm cover should be 200-300mm away from the welding point as much as possible, and the required air volume should be doubled every 10cm away;

管网风速:主管15–18m/s、支管不低于12m/s,风速不够粉尘在弯头里安家,半年堵管;

Pipeline wind speed: The main pipe has a wind speed of 15-18m/s, and the branch pipe has a wind speed of not less than 12m/s. If the wind speed is not enough, dust will settle in the elbow and the pipe will be blocked for six months;

防火先做功课:焊烟带火星,前端必须火花捕集+沉降,滤筒用阻燃防静电材质,铝镁焊再加防爆泄压。

First, do homework on fire prevention: weld smoke with sparks, the front end must be spark trapped and settled, the filter cartridge should be made of flame-retardant and anti-static materials, aluminum magnesium welding should be used, and explosion-proof pressure relief should be added.

运维看压差表:反吹清灰后吸力不恢复、压差持续超1500Pa、出风口见尘,就该换滤筒了。滤筒不能水洗,正常寿命6–12个月,别等穿透再动。

Operation and maintenance check the differential pressure gauge: If the suction force does not recover after blowing back the dust, the differential pressure continues to exceed 1500Pa, and dust is seen at the air outlet, it is time to replace the filter cartridge. The filter cartridge cannot be washed with water and has a normal lifespan of 6-12 months. Do not wait for penetration before moving.

车间整体通风也要同步做,只靠除尘器不补新风,负压一乱,烟就往操作位回窜。

The overall ventilation of the workshop should also be synchronized, relying solely on the dust collector without replenishing fresh air. If the negative pressure is disrupted, smoke will flow back to the operating position.

本文由焊烟除尘设备友情奉献.更多有关的知识请点击:http://www.sdcjtz.com我们将会对你提出的疑问进行详细的解答,欢迎你登录网站留言.

This article is a friendly contribution from Welding Smoke Dust Removal Equipment For more information, please click: http://www.sdcjtz.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

: 18563723072 : sdcjtz@126.com : 山东省德州市齐河县经济开发区名嘉西路9号

扫码添加微信了解更多

山东创杰智慧装备科技有限公司    备案号:鲁ICP备20008313号 鲁公网安备 37142502000144号   网站地图 XML TXT