工业涂装流水线的操作说明
自动涂装加工工艺属于小规格大批量自动化生产工艺形式，利用了自动喷涂、低温快速固化、高速运行的生产流水线，选用漆膜干燥快、光泽高、鲜映度好，固色性能佳的聚氨脂PU涂料，大批量生产具有鲜艳外观，手感佳的瓶盖外壳件。那么工业涂装流水线的操作说明是什么呢？
The automatic coating processing technology belongs to the form of small-scale and large-scale automated production technology. It utilizes a production line with automatic spraying, low-temperature rapid curing, and high-speed operation. It selects polyurethane PU coating with fast drying, high gloss, good clarity, and excellent color fixing performance for the paint film, and produces bottle cap shell parts with bright appearance and good hand feel in large quantities. What are the operating instructions for industrial painting assembly lines? 
1、工业涂装流水线的电器操作简要工业涂装流水线的电源需要三相四线，外面装有总开关一个，（可用三相四线四开关，也可以用开关只控制三相电源，注意一定不能将二种接法的零线也经过另外一个开关。
1. The electrical operation of the industrial painting assembly line is brief. The power supply of the industrial painting assembly line needs to be three-phase four wire, with a main switch installed on the outside. (Three phase four wire four switch can be used, or the switch can be used to control only the three-phase power supply. Note that the neutral wire of the two connection methods must not pass through another switch.).
2、启动电动机的方法： 先接通电源，此时三盏电源指示灯全部都会亮，证明三相电源已经到配电箱。此时可以按一下电机开的蓝色按钮，就可启动电机，假如不能启动，可以打开配电箱门，看一下一排的二个开关，红色长、蓝色的短。如果不是将此蓝色的压下去就可。电动机启动之后，然后打开工业涂装流水线调速表的开关，再将调速表的电位器慢慢往上调，使转速表达到想要的速度。关机时先将调速表的电位器慢慢往下调至零，然后关闭调速表开关，再按一下电机关红色按钮，就可停止电机。然后将总开关关闭。
2. The method of starting the motor: First, connect the power supply. At this time, all three power indicator lights will light up, proving that the three-phase power supply has arrived at the distribution box. At this point, you can press the blue button to start the motor. If it cannot be started, you can open the distribution box door and check the two switches in a row, the red one is long and the blue one is short. If you don't press down on this blue one. After starting the electric motor, turn on the switch of the speed control meter on the industrial painting assembly line, and slowly increase the potentiometer of the speed control meter to express the desired speed. When shutting down, first slowly lower the potentiometer of the speedometer to zero, then turn off the speedometer switch, and press the red button to stop the motor. Then turn off the main switch.
3、日光灯启动按一下照明的蓝色按钮，就可启动日光灯，再按一下照明的红色按钮，就可以停止日光灯。日光若灯不亮，请检查日光灯支架上的平开关是否打开处于1的位置。随后检查一排第三个，第四个是否处于打开位置。
3. To start the fluorescent lamp, press the blue button for illumination, and then press the red button for illumination to stop the fluorescent lamp. If the fluorescent light is not on, please check if the flat switch on the fluorescent light bracket is turned on and in the 1 position. Then check if the third and fourth rows are in the open position.
上述就是工业涂装流水线的操作说明，每个仪器的都有自己的操作步骤，所以建议大家在操作时一定要严格按照上述的操作进行哦。
The above are the operating instructions for the industrial painting assembly line. Each instrument has its own operating steps, so it is recommended that everyone strictly follow the above operations when operating.
本文由 工业涂装流水线 友情奉献.更多有关的知识请点击 http://www.sdcjtz.com/ 真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.
This article is a friendly contribution from the industrial painting assembly line For more related knowledge, please click http://www.sdcjtz.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.
鲁公网安备 37142502000144号